Unterstützte Kommandos

Die folgenden Tabellen zeigen, welche Kommandos vom Prescribe-Emulator zur Zeit unterstützt werden. Zu den in der Farbe blau dargestellten Kommandos gibt es weitere Informationen, die eventuelle Unterschiede zu den Kyocera-Druckern aufzeigen, oder Informationen, wie dieses Kommando an die Gegebenheiten des angeschlossenen Druckers angepasst werden kann.

Diese Informationen können mit einem Klick auf das Kommando angezeigt werden.

Kommandos mit drei Buchstaben

Kommando Beschreibung
ARC draw filled-in arc
BLK draw draw filled-in block
BOX draw box
CID configure color image data
CIR draw circle
DAF delete all fonts
DAM delete all macros
DAP draw to absolute position
DRP draw to relative position
DZP draw to zero-relative position
EPL EcoPrint level
JOG jog output stacks for separation
MAP move to absolute position
MRP move to relative position
MZP move to zero-relative position
PAT select fill pattern
PIE draw pie chart
RES reset
RPF return to previous font
RPG return to previous graphics state
RPP return to previous position
RPU return to previous units
SBM set bottom margin
SCF save current font
SCG save current graphic state
SCP save current position
SCS set character spacing
SCU save current units
SDP store dashed pattern
SEM set emulation mode
SFA set bitmap font attributes
SIR set image refinement level
SLM set left margin
SLS set line spacing
SPD set pen diameter
SPL set page length
SPO set page orientation
SPW set page width
SRM set right margin
SRO set raster option
STM set top margin
STR set dot resolution
UOM unit of measurement per dots



Kommandos mit vier Buchstaben

Kommando Beschreibung
ACLI add color by index
ALTF change to alternate font
AMCR call automatic macro
BARC draw standard barcode
CALL call macro
CASS select paper source
CLSP close path
CMNT comment
COPY copies per page
CPTH character path
CSET change symbol set by symbol set id
CTXT print centered text
DELF delete font
DELM delete macro
DPAT select dashed pattern
DRPA draw to relative position by angle
DUPX select/deselect duplex mode
DXPG select duplex page side
ENDM end macro
ENDR end raster data
EXIT exit from prescribe mode

Kommandos mit vier Buchstaben (Fortsetzung)

Kommando Beschreibung
FILL fill closed path
FLAT set flatness
FLST print font list
FOLD fold
FONT change current font
FPAT generate fill pattern
FRPO firmware reprogram
FSET change font setting by characteristic
FTMD bitmap font mode
GPAT set gray pattern
GRAY represent gray
INTL international characters
JOBS job start
JOBT job terminate
MCRO define macro
MRPA move to relativ position by angle
MTYP select media type
NEWP start new path
OTRY select paper output tray
PAGE start new page
PARC in path draw arc
PDIR set print direction
PDRP in path, draw to relative position
PDZP in path, draw to zero rel. position
PMRA in path, move to rel. pos. by angle
PMRP in path, move to relative position
PMZP in path, move to zero-rel. position
PNCH punch
PRBX in path, draw round box
PRRC in path, at rel. pos., draw arc
PSRC select paper source
PXPL pixel placement
RESL set resolution
RGST offset registration
RPCS return to previous code set
RPPL return to previous palette
RTTX rotate text
RTXT print right-aligned text
RVCD receive compressed raster data
RVCL receive color raster data
RVRD receive raster data
SCAP set line cap
SCCS save current code set
SCOL select color
SCPI set characters per inch
SCPL save current palette
SCRC set command recognition character
SETF set alternate font
SFNT select current font by typeface
SHMI set horizontal motion index
SIMG set image model
SIMP create simple color palette
SLJN set line join
SLPI set lines per inch
SLPP set lines per page
SMLT set miter limit
SPSZ set paper size
SROP set raster operation
STAK select paper stacker
STPL staple
STRK stroke current path
SULP set underline parameters
TEXT print text
UNIT set unit of measurement
WIDE set wide a4 mode
XBAR two dimensional barcode PDF417
XBCP parameter of 2d barcode PDF417
XPAT generate expanded fill pattern