Die folgenden Tabellen zeigen, welche Kommandos vom Prescribe-Emulator zur Zeit unterstützt werden. Zu den in der Farbe blau dargestellten Kommandos gibt es weitere Informationen, die eventuelle Unterschiede zu den Kyocera-Druckern aufzeigen, oder Informationen, wie dieses Kommando an die Gegebenheiten des angeschlossenen Druckers angepasst werden kann.

Diese Informationen können mit einem Klick auf das Kommando angezeigt werden.

Kommandos mit drei Buchstaben Kommando Beschreibung ARC draw filled-in arc BLK draw draw filled-in block BOX draw box CID configure color image data CIR draw circle DAF delete all fonts DAM delete all macros DAP draw to absolute position DRP draw to relative position DZP draw to zero-relative position EPL EcoPrint level JOG jog output stacks for separation MAP move to absolute position MRP move to relative position MZP move to zero-relative position PAT select fill pattern PIE draw pie chart RES reset RPF return to previous font RPG return to previous graphics state RPP return to previous position RPU return to previous units SBM set bottom margin SCF save current font SCG save current graphic state SCP save current position SCS set character spacing SCU save current units SDP store dashed pattern SEM set emulation mode SFA set bitmap font attributes SIR set image refinement level SLM set left margin SLS set line spacing SPD set pen diameter SPL set page length SPO set page orientation SPW set page width SRM set right margin SRO set raster option STM set top margin STR set dot resolution UOM unit of measurement per dots Kommandos mit vier Buchstaben Kommando Beschreibung ACLI add color by index ALTF change to alternate font AMCR call automatic macro BARC draw standard barcode CALL call macro CASS select paper source CLSP close path CMNT comment COPY copies per page CPTH character path CSET change symbol set by symbol set id CTXT print centered text DELF delete font DELM delete macro DPAT select dashed pattern DRPA draw to relative position by angle DUPX select/deselect duplex mode DXPG select duplex page side ENDM end macro ENDR end raster data EXIT exit from prescribe mode

Kommandos mit vier Buchstaben (Fortsetzung) Kommando Beschreibung FILL fill closed path FLAT set flatness FLST print font list FOLD fold FONT change current font FPAT generate fill pattern FRPO firmware reprogram FSET change font setting by characteristic FTMD bitmap font mode GPAT set gray pattern GRAY represent gray INTL international characters JOBS job start JOBT job terminate MCRO define macro MRPA move to relativ position by angle MTYP select media type NEWP start new path OTRY select paper output tray PAGE start new page PARC in path draw arc PDIR set print direction PDRP in path, draw to relative position PDZP in path, draw to zero rel. position PMRA in path, move to rel. pos. by angle PMRP in path, move to relative position PMZP in path, move to zero-rel. position PNCH punch PRBX in path, draw round box PRRC in path, at rel. pos., draw arc PSRC select paper source PXPL pixel placement RESL set resolution RGST offset registration RPCS return to previous code set RPPL return to previous palette RTTX rotate text RTXT print right-aligned text RVCD receive compressed raster data RVCL receive color raster data RVRD receive raster data SCAP set line cap SCCS save current code set SCOL select color SCPI set characters per inch SCPL save current palette SCRC set command recognition character SETF set alternate font SFNT select current font by typeface SHMI set horizontal motion index SIMG set image model SIMP create simple color palette SLJN set line join SLPI set lines per inch SLPP set lines per page SMLT set miter limit SPSZ set paper size SROP set raster operation STAK select paper stacker STPL staple STRK stroke current path SULP set underline parameters TEXT print text UNIT set unit of measurement WIDE set wide a4 mode XBAR two dimensional barcode PDF417 XBCP parameter of 2d barcode PDF417 XPAT generate expanded fill pattern